Everbuild 901 Black Jack Bitumen Paint 5 Litre

Black Bitumen Paint is a solvent based, full bodied black bituminous paint. When dry, the product forms an odourless and taint free black film suitable for metal protection, concrete structures and overcoating wood and felt.

Fast drying paint
Suitable for use on most common building surfaces
Resistant to most salt solutions, dilute acids and alkalis, water and alcohol
Provides a waterproof, weatherproof and corrosion-resistant protective coating

PRODUCT DESCRIPTION
EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT
is a solvent-based, full-bodied black bituminous paint.
When dry, the product forms an odourless and taintfree black film suitable for metal protection as well as overcoating wood and felt.

USES
EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT provides an effective waterproof, weatherproof, corrosion-resistant protective coating. It is resistant to low concentrations of alkalis and acids and can withstand prolonged oxidation. It is suitable for application to a wide variety of materials including iron, steel, lead, zinc, aluminium, asbestos-cement, concrete, stone, wood, felt and brick and is mainly used for:
Metal protection - corrugated iron sheets, fire escapes, stairways, ladders, storage tanks, gutters, downpipes, fences, railings, gates etc.
As a protective coating for concrete structures, stone, brick, concrete screeds and sand/cement surfaces.
Overcoating felt/wood.

CHARACTERISTICS / ADVANTAGES
▪ Fast drying.
▪ For use on most common building surfaces.
Type of Solvent: White spirit
Flashpoint: ca. 40°C
Film Thickness Per Coat @ 11m2 / Ltr
Wet – 0.1mm
Dry – 0.05mm
Chemical And Water Resistance: Resistant to: most salt solutions, dilute acids and alkalis, water and alcohol.
Not resistant to: oils, solvents and some detergent solutions
Service Temps: -20°C to +50°C

PRODUCT INFORMATION:
Storage Conditions EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT contains a flammable solvent, and all normal precautions against fire must be taken during both storage and use. Store in original container in cool (5°C - 25°C) dry conditions. Keep away from sources of ignition.
Density: ca. 0.9 g/cm3 at 20°C
Viscosity: 700-1200 cP

TECHNICAL INFORMATION:
Service Temperature: -20°C to +50°C

APPLICATION INFORMATION
Consumption / Yield / Dosage (PRINT single line): Porous surfaces: 4-6m2 Non-porous surfaces: 11m2
Ambient Air Temperature: 5°C - 40°C. Surfaces must be free from ice and water.
Drying time: 4-6 hours depending on drying conditions

APPLICATION INSTRUCTIONS:

SUBSTRATE PREPARATION
As with all surface coatings, preparation of the surface is of great importance and will influence the degree of adhesion obtained and the life of the coating. All surfaces must be sound, stable and thoroughly clean and dry. Metal surfaces should be wire-brushed to remove rust. Where long-term protection is required an initial treatment of a rust-inhibitive product such as red lead or zinc phosphate should be used. Loose or blistered paint should be removed, as should tar-based paint
systems. New galvanised surfaces should be roughened with a wire brush or treated with a proprietary etch primer. Porous surfaces should be primed with Black Jack® Bitumen & Flashing Primer.

APPLICATION
EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT is ready for use and should not be thinned. Stir thoroughly before use. Apply by brush or spray. A minimum of two coats of EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT should be applied. The first coat should be allowed to dry (normally 2-4 hours depending on weather conditions) before the second coat is applied.
Protective coating on concrete, etc: since concrete and some stone surfaces may be porous, an initial primer coat of EVERBUILD® BITUMEN PRIMER should be applied.

CLEANING OF TOOLS
Tools may be cleaned by using white spirit. Any spillage should be wiped off surfaces before the bitumen paint has set.

LIMITATIONS
Do not use in areas where subsequent solvent contact is likely.
▪ Do not use for potable drinking water tanks.
▪ Avoid inhalation of vapours in confined spaces.
▪ Allow sufficient drying time between coats.
EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT may bleed through any paints subsequently applied over it. Apply a primer recommended by the
paint manufacturer before overpainting.